![]() Now, for the first point, in this case, it really doesn't matter where I pick since these objects just need to move relative to where they are right now, so I'll just go ahead and type in zero here, rather than having to even mess with the viewport. So let's bring up move again, so transform move, and I'll go through the same steps, I'll select my objects, and this time I'll grab all three of these, so I'll just do a window selection to grab these objects here. Okay, lets try another move, and, this time, I'd like to move these shapes exactly 10.25 units in this direction, so kind of diagonal in the Y and Z directions at the same time. And there you go! My cone and sphere are perfectly aligned. And I'll just click once more, to set that point. And you can see I'm snapping right to the top of that sphere. Let's go over there on that, zoom in a little bit. So I'll click to set that point, and then for the point to move to, I'll pick the end point that's right at the top of the sphere. ![]() So I'll pick my object to move, which is the cone, and hit Done, and then I'll pick the point to move from, and while this could be any point, in this case, since I'd like the cone to be right on the tip top of that sphere, I'll pick the center point of the cone's base for the point to move from, and, since I have object snaps on, I should be able to snap right to it, and I can see I'm snapping right to center of the base of that cone. Before we start, I'll go ahead and activate my end and center object snaps, and then let's bring up the move command, so transform move. Now, if I were doing that with click and drag, it would be really hard, so if I was trying to sort of line this up, I'd have to go through multiple viewports, and even then, it might not line up as precisely as I'd like it to, so I'll hit command z to go back, and let's try that again with the move command. So, for example, let's say that I'd like to place my cone right on the very tip top of my sphere. And move is great, since we can use it in combination with object snaps, or by typing precise numbers into the command prompts. So, sometimes when we're modeling in Rhino, we need to make more precise movements, and for that was can use the move command, which we can find under the transform menu. I'm just going to hit command z a couple times to get these objects back lined up to how I had them originally. So I could do that from the front, and also from the right. And basically, elevator mode lets us move in the direction that's perpendicular to the construction plane of whatever view we're in. So notice now, instead of moving along the top construction plane, I'm moving actually up and down, that's kind of why it's called elevator mode. So, I'm holding down command and just clicking and dragging. Now, I can modify the direction by using what's called elevator mode, and to do that, we just hold the command key and then click and drag, so let's try that in perspective. So with click and drag, we're moving in at most two directions at once. And then in the right viewport, I'm moving in the YZ or right construction plane. Similarly, when I move in the front viewport, I'm moving in the XZ or front construction plane. So, notice when I click and drag in perspective, I'm moving along the XY or top construction plane, and this is the same construction plane that's in the top viewport, so that move should look the same in top and perspective. Now, depending on which one we're in, our movements will be constrained to one of the default construction planes. And we can do this from any of the viewports. ![]() ![]() So I can click and drag on any object to move it, or I could shift select to grab multiple objects and move those all at the same time. And a lot of times, that's just fine to move something just so it looks good visually. Now, the simplest way to move an object in Rhino is to click and drag, and this is also the least precise way to move something. So, let's get moving with transform-move.3dm from the exercise files, and here I've just got a few simple shapes for us to practice with. We can simply click and drag in the viewport, we could use the move command, or we could use the gumball tool, and they all accomplish pretty much the same thing, each just in a slightly different way. Now, we've got a few different options for how we can move things. That is the ability to move objects around in Rhino's 3d space. Let's talk about a fundamental modeling skill you'll need for just about any job in Rhino 5 for Mac.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |